All buyer guides · · OPINOX
If Moldflow predicts a weld line near a load-bearing boss, use the prediction to identify where to look and what to test. Check the first molded parts with the intended fasteners and applied loads. A photo of the line or a simulation plot alone cannot establish the strength of the actual joint.
In this guide
- Compare predicted and observed locations
- Use actual joint conditions to judge acceptance
- Identify the loads the boss actually has to carry
- Use the Moldflow result to choose a useful inspection area
- Control the test sequence and keep separate specimens where needed
- Decide whether to revise the part, the tool or the trial
- Review side effects before moving the line
- RFQ questions and answers
Compare predicted and observed locations
Autodesk describes the weld-line result as showing where flow fronts meet and their convergence angle. A line may matter for strength, appearance or both. Record the material, part and gate configuration used in the simulation. On pilot parts, mark the observed line relative to the boss and the load direction, and keep magnified photographs if the contrast is low.
An example is a fastener boss close to a connector opening. The opening may split the flow, which can rejoin near the boss. Compare the projected line with the physical sample. If the line is faint or lands somewhere else, document that observation and ask the tooling team to check the test and simulation inputs.
Use actual joint conditions to judge acceptance
Build the functional check around the load applied to the boss in service. For a mounted housing, that might mean installing the specified screw and bracket, setting the agreed tightening torque, and then applying the intended load direction in a fixture. Agree with engineering on the acceptance threshold and whether repeated tightening, sustained load or conditioning should be included.
Record where the first damage occurs, such as a crack crossing the weld line or a fracture starting at the boss root. Retain representative passing and failing specimens where practical so the location can be checked after revisions.
- A drawing marking each load-bearing boss and the expected assembly and service loads.
- Simulation inputs and plots linked to the actual revision and molding material.
- Pilot samples labeled by cavity and molding condition where available.
- A test plan with acceptance limits, fixture method and a place to record the failure location.
Identify the loads the boss actually has to carry
Ask the product engineer to mark what the boss does on the assembled drawing. A screw boss that clamps a decorative cover sees a different duty from one that carries a bracket or reacts a cable load. For every critical boss, identify the mating part, its direction of movement and any leverage from the distance between the boss and the applied force. Include severe foreseeable assembly conditions if the specification already calls them out.
Draw the support points as well as the load direction. If a housing is attached through two mounting points, its installed support may spread load differently from a test performed on a loose shell. A pull test on the boss alone can be useful for comparing versions, but a representative assembly test is needed when stiffness of the housing or bracket influences the load path. Specify which question each check addresses.
Mark the space where damage is especially costly, for example a boss directly behind a visible face or near the surface that positions a connector. That makes it easier to choose which parts to inspect first and which design changes might create another problem.
Use the Moldflow result to choose a useful inspection area
The analysis is more helpful when its inputs travel with the image. Save the drawing revision, assumed resin, proposed gate layout and simulation settings with the plot. Include a corresponding view of fill time where available. Autodesk describes looking at fill progression to see where flow fronts approach and rejoin. A screenshot with no part orientation or gate location makes it harder to compare the plot against the first molded parts.
Look beyond the nearest line on the plot. Check whether the predicted line crosses the boss root, a reinforcing rib or the wall next to the boss. Ask the design owner to flag the region where a crack could affect function. Then decide whether the physical inspection should concentrate on one boss, more than one cavity, or another area such as a nearby window that changes the melt flow.
Hypothetical example: a connector opening splits flow across one side of an instrument case. The predicted line appears near the upper screw boss. The lower boss has the same diameter and no nearby opening. Comparing the two areas can give context, provided the trial team records the break points and acknowledges any differences in support. It does not isolate the weld-line effect by itself.
Control the test sequence and keep separate specimens where needed
Begin with a visual and dimensional check before applying a load. Record line location and any unexpected marks. Use the actual screw length and the specified seating condition during assembly. A screw that bottoms out or an uneven support surface can produce misleading torque or fracture observations. Photograph the fixture setup and agree how it will be repeated if a revised sample arrives.
If the project needs a static load check and a repeated service check, plan where to use separate specimens. The first test may change a boss enough to affect the following result. For a repeatability comparison, ask whether the sample set can include the identifiable cavities or agreed trial conditions. Keep as-molded and already-tested specimens labeled so the records cannot be confused.
Decide how to record borderline cases before testing. If a part deforms but springs back, if a screw continues rotating, or if a hairline crack appears with the part still assembled, log what happened and when. A pass or fail flag alone loses the detail needed to evaluate a later tooling change.
Decide whether to revise the part, the tool or the trial
When a sample fails, compare the physical fracture point with the predicted and observed line positions. If the fracture begins in a thin boss root and runs across the line later, do not assume the line caused the first fracture. Ask the project team to consider the geometry, assembly load and process together. A quick isolate-and-repeat check can be more informative than changing several variables at once.
If your supplier proposes moving a gate, have it explain how the new flow pattern affects the other screw bosses, ribs, visible faces and venting. If it proposes changing the local section, review the drawing with the mating parts. Proposed process changes should be checked with the selected resin and project requirements before they are considered valid for a production release.
Set the handoff condition in writing. Issue the accepted drawing revision with the tested samples, lot or cavity information if recorded, photographs, fixture description and any remaining open checks. If the production tool or gate configuration will differ from the pilot tool, decide which critical test must be repeated before relying on the pilot approval.
Review side effects before moving the line
Autodesk identifies gate position and part thickness as possible ways to move a weld line. Review any proposal in context: a gate change may move the line toward another stressed feature or a visible surface. Compare the revised flow prediction and repeat the same functional check on samples before accepting the change.
Buyer questions
Is every weld line by a screw boss a reject?
Check the drawing and agreed performance or appearance limits. A line near a stressed section warrants targeted testing, and a cosmetic limit can apply independently of strength.
What if the simulation predicts no visible line at the boss?
Use the prediction to guide inspection. Check production-intent samples because the actual material, processing conditions and layout can affect where the fronts meet and how the part behaves.
RFQ questions and answers
Do I need to include a Moldflow study in the RFQ?
Send an existing study if it matches the current part and material assumptions. If you need a new one, identify the gate alternatives, critical bosses and intended resin. Ask the supplier to quote the study scope and specify which reports and model assumptions will be included.
What should a supplier price for the first molded shots?
Request a quote with separate descriptions for the pilot tool, molded samples, visual and dimensional inspection, and any fixture or load test. Attach the drawing with the critical regions highlighted so suppliers can see exactly what their sample work covers.
Can I request both cosmetic and strength checks on the same line?
Yes. Provide separate acceptance criteria for visible marks and loaded performance, plus the appropriate viewing or test conditions. Plan distinct specimens if loading would affect the appearance assessment or if the same piece needs to be retained as a reference.
How many parts should I request from each cavity?
Ask the supplier for the proposed sample distribution and confirm the count with your engineering or quality team. The count depends on the test method, cavity count, expected variation, destructive tests and the decision the results need to support.
How should I quote a possible change of gate location?
Ask for a comparison of the initial and alternative gate layouts with revision drawings, study scope and any tool change cost. Request a plan for repeating the same functional test and reviewing the lines at other critical locations after the change.
Related products and services
- Review moldability for load-bearing plastic features →
- Specify functional checks for the first molded shots →
Discuss this project with OPINOX →

