All buyer guides · · OPINOX
A heat-set insert goes into an already molded boss. A molded-in insert is held in the tool while plastic is injected around it. Choose which process to sample using the required joint loads, assembly access and expected production quantity. Approve the joint on representative molded parts with the specified screw and documented test criteria.
In this guide
- Compare tooling and assembly requirements
- Specify separate tests for pull-out and torque
- Start with a fastener stack that can actually be assembled
- Specify the boss and insert as matched parts
- Keep the two processes comparable in the sample plan
- Read the failure mode before choosing a process
- Use the intended assembly for service-cycle checks
- RFQ questions and answers
Compare tooling and assembly requirements
Protolabs describes heat installation as an operation performed after molding. The boss must have a receiving hole with a lead-in and enough surrounding material for the installation method. Use the chosen insert manufacturer's drawing for the boss and hole dimensions. Show where the installation tip and supporting fixture can reach the part.
For a molded-in insert, ask how the tool will locate it, keep plastic out of the threads and hold the seating height. Compare the tooling cost and how each insert will be loaded with the labor and inspection needed after molding. The appropriate comparison includes both operations and their effects on the finished joint.
Specify separate tests for pull-out and torque
An axial pull-out test measures how the insert and boss resist extraction. A torque check addresses a different question, including whether the insert turns in the boss before the required assembly torque is reached. Define which outcomes matter and ask your engineering team to set acceptance limits and test conditions from the intended load case.
Record fastener size and engagement, fixture support, insert and resin lots, boss dimensions, installation method and the failure mode. Retain photographs showing whether the insert moved, the boss cracked or the screw thread failed.
- Drawing showing the boss geometry, insert part number, insertion depth and thread callout.
- Actual screw and clamped stack, including the washer or mating part if used.
- Agreed pull-out, torque and repeated assembly criteria and sample quantities.
- A comparison record that ties each result to the molded part, resin and insert installation method.
Start with a fastener stack that can actually be assembled
Identify what the screw threads into and what the screw head clamps. For a service cover, a typical stack might be the cover, a spacer or gasket if fitted, and the insert in the main enclosure. Draw the assembly at both ends of your tolerance range. Check how far the screw tip enters the insert when the cover is fully seated, and check that it cannot bottom out before generating the intended clamp. A joint that feels tight because the screw has bottomed may still leave the cover loose.
Give each installation a load direction. Is the insert holding a cover against a gasket, supporting a bracket that can be pulled away, or holding a board that passes load into adjacent ribs? Indicate where the load enters the housing and where a fixture should react it. If multiple inserts share a load, a test of one isolated boss and a test of the assembled product answer different questions. Identify which one is needed for your decision.
Agree what normal service includes before specifying cycles. Opening a cover for inspection is a different duty from repeated disassembly on a manufacturing bench. Supply the intended driver, tightening method and expected sequence so the sample check includes the same handling as the finished assembly.
Specify the boss and insert as matched parts
An insert part number is more useful than a thread description alone. Different inserts can have the same internal thread and different external shapes, lengths, lead ends and retention features. The outer geometry and how the resin is placed around it affect the joint. Ask your supplier to show how the proposed boss matches the specific insert before fixing the CAD. Record the agreed part number or have the design owner approve equivalents.
For heat-set installation, identify where the insert stops and how the tool aligns it. A flat reference surface, access for the insertion tip and support that prevents the boss from bending can help make the installation consistent. Discuss whether to confirm seating visually or with a depth check. For molded-in installation, mark the thread opening that must remain clear and ask how the insert will be held during the molding cycle.
A section drawing should show the boss root, the outside diameter or adjacent walls, the remaining plastic under the insert, and any rib or fillet tied into the boss. Ask the tooling team to review those features together. If it proposes adding support that affects a visible surface or board clearance, confirm the interface before release.
Keep the two processes comparable in the sample plan
Set up sample labels before the first run. For a comparison using two installation methods, record whether both are made with the same grade and color of resin and whether the boss geometry is identical or specific to each method. Where geometries differ, the test compares two joint designs. Keep assembly hardware, applied loads and inspection method consistent so the result can still support a fair decision.
Illustrative example: a handheld instrument has a service lid with four screws and one boss close to a thin edge. The buyer wants to know whether later access will loosen that corner. Include that corner in the inspection, and ask the supplier to mark where the fixture supports the housing. Testing a well-supported center boss would miss the installation access and restraint issues at the corner. Keep the case tied to your own drawing and test limits.
For pull-out, agree how the screw or load adapter engages the insert, how much material is supported around the boss and in which direction the joint is loaded. For torque, use the agreed driver and distinguish thread damage from rotation within the boss. Where conditioning is relevant to the application, agree in advance how samples will be stored or conditioned before testing.
Read the failure mode before choosing a process
A single maximum reading tells you when a specimen failed under that setup. The way it failed tells you where to look. A tilted insert points to a different issue from a straight insert that pulls out while the surrounding boss stays intact. A crack starting at the boss root deserves a check of the geometry and part support. Damaged threads deserve a separate check of the fastener, thread condition and engagement.
If the joint falls short, record which test ran first and whether previous tightening or loading may have changed the part. Specify separate specimens where a destructive test would affect another result. When you compare a redesign with the baseline, use the same fixture and loading direction and keep the changed factors visible. A change to a fastener, insert or boss should all be reflected in the test record.
After one version is approved, attach the sample ID, drawing revision, installation method and acceptance record to the purchase specification. If production changes the insert, switches the resin or changes how the boss is supported during installation, ask whether the earlier approval covers that change. This gives the buyer and supplier a repeatable baseline for later lots.
Use the intended assembly for service-cycle checks
If the part is meant to be opened for maintenance, repeat the removal and refitting procedure using the prescribed tightening method. After the agreed number of cycles, check if the screw engages smoothly, if the insert has moved and if the joint still closes correctly. Keep destructive samples separate from those used for dimensional or cosmetic approval.
Buyer questions
Can the same boss drawing serve both heat-set and molded-in inserts?
Check with the insert supplier and mold maker. Post-mold installation needs a receiving hole and tool access. Molded-in installation needs locating and thread protection in the molding tool. The two methods can require different interfaces.
Can a printed prototype confirm insert pull-out strength for production?
A print can help check access and geometry. Use molded samples with the intended resin, boss and insert process when approving performance of the production joint.
RFQ questions and answers
What files should I send to quote both insert options?
Send the plastic part CAD, insert manufacturer drawing, assembled section and details of the mating screw and clamped parts. Add the resin grade if known, expected sample and batch quantities, insert positions and the acceptance checks required for your intended use.
Can the tooling and assembly costs be quoted separately?
Request separate line items for tooling, insert hardware, assembly and sample testing. Ask the supplier which allowances depend on the actual drawing or production volume. A molded-in option may change mold features and insert handling, while a heat-set option may need a dedicated fixture and inspection.
Which sample checks should be included in the quote?
Ask for seating depth, presence and thread inspection, plus actual assembly with the supplied screw. Include torque, axial pull-out or repeat-cycle testing if the joint needs it. Provide agreed methods and quantities so suppliers quote the same scope.
How should the first batch be split for inspection?
Agree how many pieces to reserve for fit and cosmetic approval and how many to use for each destructive test. Ask whether samples can be labeled by cavity, insert lot and process where this information is available, and list the records you expect with them.
What should I get back with the quoted recommendation?
Request the recommended insert part number, a section showing the proposed boss and seat, the reason the process fits your project, and which details still need confirmation. If a critical test is excluded, ask for its cost and lead-time impact as a separate line item.
Related products and services
- Plan first molded samples for threaded joint testing →
- Review bosses and insert geometry before tooling →
Discuss this project with OPINOX →

